Over 15 years experience of providing support of MEAN WELL Power Supplies
Overview
ISI-501-248D is the model of this series: rated power 500W, typical efficiency 88%.
ISI-501 series integrates a DC/AC True Sine Wave Inverter and a MPPT charger. This series is a high performance true sine wave DC/AC inverter which converts the DC electricity from a system consisting of batteries and solar panels. ISI-501 is not only a high frequency designed inverter but also fully digitally controlled by an advanced microprocessor. With true sine wave output, ISI-501 series can provide 500W continuously, 550W for 60 seconds, and 1000W for 30 AC-cycles. This series incorporates a MPPT solar charger, including the constant current and constant voltage charging characteristics.
Features
- True sine wave output (THD<3%)
- High surge power up to 1000W
- High efficiency up to 88%
- High frequency design
- Thermosstatically controlled cooling fan
- Protections: Bat. low alarm / Bat. low shutdown / Over voltage / Over temp. / Output short / Input polarity reverse / Overload
- Built-in 500W MPPT solar charger, MPPT efficiency:98%(Typ.)
- Built-in remote ON-OFF control
- Built-in battery low relay contact
- LED indicator for operation status and battery capacity
- 3 years warranty
Specifications
INVERTER SECTION
- RATED POWER
- 500W
- MAXIMUM OUTPUT POWER (Typ.)
- 550W for 60 sec. / surge power 1000W for 30 cycles (112, 212 models : 495W for 60 sec. / surge power 900W for 30 cycles)
- AC VOLTAGE
- Factory setting set at 230VAC 200 / 220 / 230 / 240VAC selectable by setting button S.W
- FREQUENCYNote.9
- Factory setting set at 230VAC 50±0.1Hz 50/60Hz selectable by setting button S.W
- WAVEFORMNote.1
- True sine wave (THD<3%)
- AC REGULATION (Typ.)
- ±3%
- FRONT PANEL INDICATOR
- Fault and operation status, Charger status, Battery capacity
- BAT. VOLTAGE
- 48V
- VOLTAGE RANGENote.3,5
- 42 ~ 60VDC
- DC CURRENT (Typ.)Note.7
- 15A
- NO LOAD CURRENT DRAW (Typ.)
- 0.32A
- OFF MODE CURRENT DRAW (Typ.)
- ≦1mA
- EFFICIENCY (Typ.)Note.2
- 88%
- OVER TEMPERATURE
- Shut down o/p voltage, re-power on to recover
- OUTPUT SHORT
- Shut down o/p voltage, re-power on to recover
- OVER LOAD (Typ.)
- 110% load for 60 sec. Protection type : Shut down o/p voltage, re-power on to recover
BATTERY SECTION
- CHARGER CURRENT (Typ.)
- 8.5A
- BATTERY TYPE
- Open & sealed Lead Acid
- FUSE
- 20A*2
- BAT. LOW ALARMNote.3
- 45V
- BAT. LOW SHUTDOWNNote.3
- 42V
- REVERSE POLARITY
- By internal fuse open
MPPT / SOLAR SECTION
- MPPT CHARGER EFFICIENCY (Typ.)
- 98%
- OPEN CIRCUIT VOLTAGE RANGE
- 90 ~ 160V
- MPPT RANGE
- 70 ~ 160V
- SOLAR INPUT CURRENT (Typ.)
- 4.5A
- SOLAR INPUT POWER (Typ.)
- 500W
GENERAL SECTION
- WORKING TEMP.Note.4
- -20 ~ +40℃ @ 100% load ; 60℃ @ 50% load
- WORKING HUMIDITY
- 20% ~ 90% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -30 ~ +70℃ / -22 ~ +158℉, 10 ~ 95% RH non-condensing
- VIBRATION
- 10 ~ 500Hz, 3G 10min./1cycle, 60min. each along X, Y, Z axes
- SAFETY STANDARDS
- IEC62368-1 CB, EAC TP TC 004 approved; Meet BS EN/EN62368-1
- WITHSTAND VOLTAGE
- Bat I/P - AC O/P:3.0KVAC AC O/P - FG:1.5KVAC
- ISOLATION RESISTANCE
- Bat I/P - AC O/P, Bat I/P - FG, AC O/P - FG: 100M ohms / 500VDC / 25℃/ 70% RH
- EMC EMISSION
- Compliance to BS EN/EN55032 class B, EAC TP TC 020
- EMC IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,8, BS EN/EN55035, EAC TP TC 020
- MTBF
- 565.4K hrs min. Telcordia SR-332 (Bellcore) ; 57.8K hrs min. MIL-HDBK-217F (25℃)
- DIMENSION
- 205*158*67mm (L*W*H)
- PACKING
- 2.35Kg; 6pcs/15.1Kg/1.55CUFT
Test conditions and notes9
- 1.THD is tested by rated power, linear load at 13V,26V,52V input voltage.
- 2.Efficiency is tested by 350W, linear load at 13V,26V,52V input voltage.
- 3.The tolerance of each voltage value by models is : 112/212→±0.5V ; 124/224→±1V ; 148/248→±2V.
- 4.Output derating capacity referenced by curve 1.
- 5.Input derating capacity referenced by curve 2.
- 6.All parameters not specified above are measured at rated load, 25℃ of ambient temperature and set to factory setting.
- 7.DC current is tested by 500W, linear load at 12V,24V,48V input voltage.
- 8.The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
- 9.Type F for 60Hz only.
Technical drawings
Typical applications
- Home appliance
- Power tools
- Portable equipment
- Yacht
- Vehicle
Downloads
Catalogues1
FAQ
What is the main use case for the Mean Well ISI-501-248D?
This model is a 500W true sine wave DC-AC inverter designed for applications that need clean AC output from a DC battery system. It is also differentiated by its built-in 500W MPPT solar charger, which makes it suitable for mobile, off-grid, and backup power systems that use solar charging.
Does the ISI-501-248D produce true sine wave output?
Yes. The ISI-501-248D provides true sine wave output with total harmonic distortion below 3%, which helps support sensitive electronics and other loads that benefit from cleaner AC power. Compared with modified sine wave units, this makes it a better fit where output quality matters.
What power level does this inverter support?
This model is rated for 500W continuous output power. It also supports surge power up to 1000W, which can help with short startup demands from some loads. Buyers should still size the inverter around the actual running power requirements of their equipment.
What DC input range does the ISI-501-248D require?
The listed DC input range for this model is 42 to 60VDC. That means it is intended for systems operating in that input window, so buyers should verify their battery system matches the inverter's rated input range. It also supports open and sealed lead acid batteries.
Does this model include a solar charger?
Yes. The ISI-501-248D has a built-in 500W MPPT solar charger with typical MPPT efficiency of 98%. That built-in feature can reduce the need for a separate charger in solar-assisted power systems using this inverter.
What protections are built into the ISI-501-248D?
This inverter includes battery low alarm, battery low shutdown, over voltage, over temperature, output short, input polarity reverse, and overload protection. For overload, over temperature, and output short conditions, the unit shuts down output and requires re-powering to recover.
Can the ISI-501-248D be used in demanding temperature conditions?
It is rated for operation from -20°C to +40°C at 100% load. The specification also states operation up to 60°C at 50% load, so performance expectations should be adjusted for hotter environments. Its built-in cooling fan is intended to support thermal management during operation.
What other buyer-focused features does this inverter include?
The ISI-501-248D includes built-in remote ON-OFF control, a battery low relay contact, and LED indicators for operating status and battery capacity. These are useful for commercial and industrial buyers who need system-level monitoring and control.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Other ISI-501 Models
24 other modelsPlease log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.



