☎ (888) 228 9138

Over 15 years experience of providing support of MEAN WELL Power Supplies

1 5

Image shown is a representation only. Exact specifications should be obtained from the product datasheet.

Mean Well

Mean Well PLN-30-9 Power Supply 30W 9V - IP64 3.3A

fully isolated plastic caseIP64suitable for signage applications
SKU PLN-30-9
$27.91 USD
Shipping calculated at checkout.
Available to order
|

Overview

PLN-30-9 is the 9V output model of this series: rated current 3.3A, rated power 29.7W, typical efficiency 80%.

Features

  • Universal AC input / Full range (up to 295VAC)
  • Protections: Short circuit / Over current / Over voltage / Over temperature
  • Cooling by free air convection
  • Built-in constant current limiting circuit with adjustable OCP level
  • Fully isolated plastic case with IP64 level
  • Built-in active PFC function
  • Pass LPS
  • Class Ⅱ power unit, no FG
  • Class 2 power unit
  • 100% full load burn-in test
  • High reliability
  • Suitable for LED lighting and moving sign applications (Note.2)
  • Compliance to worldwide safety regulations for lighting
  • 2 years warranty

Specifications

PLN-30-9Specifications from the official datasheet (2026-02-09 edition)

OUTPUT

DC VOLTAGE
9V
CONSTANT CURRENT REGIONNote.6
6.3 ~ 9V
RATED CURRENT
3.3A
CURRENT RANGE
0 ~ 3.3A
RATED POWER
29.7W
RIPPLE & NOISE (max.)Note.2
2.6Vp-p
VOLTAGE ADJ. RANGENote.5
-5% ~ 10%. Can be adjusted by internal potentiometer SVR1
CURRENT ADJ. RANGENote.5
3% ~ -25%. Can be adjusted by internal potentiometer SVR2
VOLTAGE TOLERANCENote.3
±10%
LINE REGULATION
±3.0%
LOAD REGULATION
±5.0%
SETUP TIME
500ms / 230VAC 3000ms / 115VAC at full load

INPUT

VOLTAGE RANGENote.4
90 ~ 295VAC 127 ~ 417VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.95/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
TOTAL HARMONIC DISTORTION
THD< 20% when output loading≧75% at 115VAC/230VAC input and output loading≧80% at 277VAC input
EFFICIENCY (Typ.)
80%
AC CURRENT (Typ.)
0.4A/115VAC 0.2A/230VAC 0.15A/277VAC
INRUSH CURRENT (Typ.)
COLD START 35A(twidth=25μs measured at 50% Ipeak) at 230VAC
MAX. No. of PSUs on 16A CIRCUIT BREAKER
64 units (circuit breaker of type B) / 64 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.5mA / 240VAC

PROTECTION

OVER CURRENT
100 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT
Hiccup mode, recovers automatically after fault condition is removed.
OVER VOLTAGE
10 ~ 14V Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE
Shut down o/p voltage, re-power on to recover

ENVIRONMENT

WORKING TEMP.
-30 ~ +50℃ (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY
-40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.06%/℃ (0 ~ 50℃)
VIBRATION
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY & EMC

SAFETY STANDARDS
UL879, UL1310, CSA C22.2 No. 207-M89(except for 48V), TUV BS EN/EN61347-1, BS EN/EN61347-2-13, EAC TP TC 004,IP64 approved
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
ISOLATION RESISTANCE
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION
Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (pin≧25W), Class D (>70% load) ; BS EN/EN61000-3-3; EAC TP TC 020
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55024, BS EN/EN61547, light industry level, criteria B;EAC TP TC 020

OTHERS

MTBF
4296.9K hrs min. Telcordia SR-332 (Bellcore) ; 621.4Khrs min. MIL-HDBK-217F (25℃)
DIMENSION
145*47*30mm (L*W*H)
PACKING
0.22Kg; 60pcs/14.2Kg/1.25CUFT
Test conditions and notes13
  1. 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
  2. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μf & 47μf parallel capacitor.
  3. 3. Tolerance : includes set up tolerance, line regulation and load regulation.
  4. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
  5. 5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB.
  6. 6. Please refer to "DRIVING METHODS OF LED MODULE".
  7. 7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
  8. 8. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
  9. 9. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
  10. 10. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
  11. 11. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
  12. 12. PLN-30-9 is used for any light source that exempt from the ErP-Directive (EU) 2019/2020 requirement, for example this model could be use for signalling products (including, but not limited to road-, railway-, marineorair traffic-signalling , traffic control or airfield lamps).
  13. 13. This product is not suitable for LED lighting applications in China.(It is recommended to use the LPF/NPF/XLG/XLC/XLN series in China)

Technical drawings

PLN-30-9 Mechanical Specification
Mechanical Specification
PLN-30-9 Block Diagram
Block Diagram
PLN-30-9 Derating Curve
Derating Curve
PLN-30-9 Power Factor Characteristic
Power Factor Characteristic
PLN-30-9 EFFICIENCY vs LOAD (48V Model)
EFFICIENCY vs LOAD (48V Model)

Downloads

FAQ

Can I use the PLN-30-9 for low-voltage LED signage?

Yes, it can fit low-voltage signage applications that need a 9V constant current output. This model supplies up to 29.7W at 3.3A, with a 6.3-9V constant current range.

Is the PLN-30-9 suitable for 9V decorative lighting?

It can be used for 9V decorative or accent lighting loads if the fixture is designed for constant current operation. The load needs to stay within 29.7W and 3.3A.

Can this driver power compact 9V illuminated displays?

It can work for compact illuminated displays where a 9V constant current driver is required and the total load stays inside the 29.7W limit. Its 145 x 47 x 30 mm IP64 housing also helps for enclosed lighting products.

How much 9V LED strip can the PLN-30-9 run?

Use 29.7W as the available power and divide that by the strip's rated watts per meter to estimate the maximum length. Check your strip rated power per meter and confirm the strip system is compatible with 9V output and constant current operation.

How does the PLN-30-9 compare with other 30W PLN models?

Within the 30W group, PLN-30-9 is 29.7W at 9V and 3.3A, PLN-30-12 is 30W at 12V and 2.5A, PLN-30-15 is 30W at 15V and 2A, PLN-30-20 is 30W at 20V and 1.5A, PLN-30-24 is 30W at 24V and 1.25A, PLN-30-27 is 30.24W at 27V and 1.12A, PLN-30-36 is 30.24W at 36V and 0.84A, and PLN-30-48 is 30.24W at 48V and 0.63A. The main differences are output voltage and corresponding output current across the same general power class.

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Bizum
  • Diners Club
  • Discover
  • Google Pay
  • Mastercard
  • MB WAY
  • PayPal
  • Satispay
  • Shop Pay
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

{ "id":8650616340800, "variants" :[{ "context":"default", "variant_id": 46615434821952, "sku":"PLN-30-9", "inventory_qty" : 0, "customer" :true, "custom_html" :"\u003cdiv class=\"price\"\u003e\n \u003cdiv class=\"price__default\"\u003e\n \u003cstrong class=\"price__current\"\u003e$27.91\u003c\/strong\u003e\n \u003cs class=\"price__was\"\u003e\u003c\/s\u003e\n \u003c\/div\u003e\n\n \u003cdiv class=\"unit-price relative\" hidden\u003e\u003cspan class=\"visually-hidden\"\u003eUnit price\u003c\/span\u003e\u003cspan class=\"unit-price__price\"\u003e\u003c\/span\u003e\u003cspan class=\"unit-price__separator\"\u003e \/ \u003c\/span\u003e\u003cspan class=\"unit-price__unit\"\u003e\u003c\/span\u003e\u003c\/div\u003e\n\n \u003cdiv class=\"price__no-variant\" hidden\u003e\n \u003cstrong class=\"price__current\"\u003eUnavailable\u003c\/strong\u003e\n \u003c\/div\u003e\n\n \u003c\/div\u003e", "volume_html" :"\u003cvolume-pricing class=\"parent-display inside_product_form\" id=\"volume-pricing-main\" \u003e\u003c\/volume-pricing\u003e" } ] }
Mean Well PLN-30-9 Power Supply 30W 9V - IP64 3.3A
Mean Well

Mean Well PLN-30-9 Power Supply 30W 9V - IP64 3.3A

$27.91 USD

PLN-30-9 is the 9V output model of this series: rated current 3.3A, rated power 29.7W, typical efficiency 80%.

Features

  • Universal AC input / Full range (up to 295VAC)
  • Protections: Short circuit / Over current / Over voltage / Over temperature
  • Cooling by free air convection
  • Built-in constant current limiting circuit with adjustable OCP level
  • Fully isolated plastic case with IP64 level
  • Built-in active PFC function
  • Pass LPS
  • Class Ⅱ power unit, no FG
  • Class 2 power unit
  • 100% full load burn-in test
  • High reliability
  • Suitable for LED lighting and moving sign applications (Note.2)
  • Compliance to worldwide safety regulations for lighting
  • 2 years warranty
View product

  • Call us

    (888) 228 9138

  • Email us

    contact@wellforces.com

  • Business Hours

    Mon-Fri
    EST 9:00am-5:30pm

  • Wholesale and Trade Account

    Let's grow together
Back to top