Over 15 years experience of providing support of MEAN WELL Power Supplies
Overview
SKA20A-05 is the 5V output model of this series: rated power 20W, typical efficiency 87.5%.
Features
- 2"×1" compact size
- 2:1 wide input range
- High efficiency up to 89.5%
- 1500VDC I/O isolation
- Built-in remote ON/OFF control
- Built-in trimming output
- Built-in EMI filter
- Protections: Short circuit / Overload / Input and Output Over voltage
- Cooling by free air convection
- Six-sided shielded metal case
- 100% burn-in test
- Low cost / High reliability
- Approvals: FCC / EAC / CE / UKCA
- 2 years warranty
Specifications
OUTPUT
- DC VOLTAGE
- 5V
- CURRENT RANGE
- 400 ~ 4000mA
- RATED POWER
- 20W
- RIPPLE & NOISE (max.)Note.2
- 50mVp-p
- LINE REGULATIONNote.3
- ±0.2%
- LOAD REGULATIONNote.4
- ±0.5%
- VOLTAGE ACCURACY
- ±2.0%
- SWITCHING FREQUENCY
- 300KHz typ.
- EXTERNAL CAPACITANCE LOAD (max.)
- 1000uF
- EXTERNAL TRIM Adj. RANGE(Typ.)
- ±10%
INPUT
- VOLTAGE RANGE
- 9 ~ 18VDC
- EFFICIENCY (Typ.)
- 87.5%
- DC CURRENT Full load
- 1910mA
- DC CURRENT No load
- 80mA
- FILTER
- Pi network
- REMOTE CONTROL
- Power ON : R.C ~ -Vin > 2.5V ~ 30VDC or open circuit ; Power OFF : R.C ~ -Vin < 0.5VDC or short
PROTECTION (Note. 5)
- PROTECTION
- Fuse recommended
- OVER CURRENT
- 110% ~ 180% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed
- SHORT CIRCUIT
- All output equipped with short circuit Protection type : Hiccup mode, recovers automatically after fault condition is removed
- OVER VOLTAGE
- >20 ~ 23VDC
ENVIRONMENT
- WORKING TEMP.
- -40 ~ +85℃ (Refer to "Derating Curve")
- WORKING HUMIDITY
- 20% ~ 90% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -55 ~ +125℃, 10 ~ 95% RH
- TEMP. COEFFICIENT
- ±0.03% / ℃ (0 ~ 50℃)
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC
- SAFETY STANDARDS
- EAC TP TC 020/2011 (EAC TP TC 004 for 48Vin type only) approved
- WITHSTAND VOLTAGE
- I/P-O/P:1.5KVDC
- ISOLATION RESISTANCE
- I/P-O/P: 100M Ohms / 500VDC / 25℃/ 70% RH
- EMC EMISSION
- Compliance to BS EN/EN55032 Class A, FCC part 15 Class A, EAC TP TC 020
- EMC IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,4,5,6,8, light industry level, criteria A, EAC TP TC 020
OTHERS
- MTBF
- 700Khrs min. MIL-HDBK-217F(25℃)
- DIMENSION
- 50.8*25.4*11.2 mm or 2"*1"*0.44" inch (L*W*H)
- PACKING
- 31.2g ; 10pcs/per tube, 400pcs/40 tube/per carton
Test conditions and notes5
- 1.All parameters are specified at normal input, rated load, 25℃ 70% RH ambient.
- 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor.
- 3.Line regulation is measured from low line to high line at rated load.
- 4.Load regulation is measured from 10% to 100% rated load.
- 5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds.
Technical drawings
Downloads
FAQ
Can I use the SKA20A-05 to power 5V embedded controllers or single-board electronics from a 9-18VDC source?
Yes, if the input source is within 9-18VDC and the electronics require 5V constant voltage. The output rating is 20W with up to 4A available, which suits higher-current 5V embedded loads within that limit.
Is this converter suitable for 5V industrial sensors, I/O, or communication modules?
It can be a fit for 5V constant-voltage industrial electronics when the total load stays at or below 4A. With 20W available, it supports more 5V current headroom than lower-power compact converters.
Would the SKA20A-05 work for a compact 5V automation subsystem inside a control panel?
Yes, provided the subsystem runs on 5V constant voltage and remains within the 20W output budget. The body size is 50.8 × 25.4 × 11.2 mm, so it is suited to compact panel or embedded spaces.
Can I use this model for 5V IT or networking support electronics that need more than 1A?
This model is better suited to higher-current 5V support electronics because it provides up to 4A at 5V. The main check is keeping the total output demand within 20W and using a source in the 9-18VDC input range.
Is the SKA20A-05 meant for outdoor use or wide-temperature environments?
The specified operating range is -40°C to +85°C, which supports a broader temperature span than many indoor-only electronics. However, no IP rating is listed in the provided specs, so the product page does not identify it as weatherproof or outdoor-rated.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Please log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.






