Over 15 years experience of providing support of MEAN WELL Power Supplies
Overview
LPC-100-1400 is the model of this series: rated current 1400mA, rated power 100.8W, typical efficiency 89.5%.
LPC-100 series is one 100W single output AC/DC LED switching power supply. It features the constant current design, providing various models with the output current ranging from 350mA through 2100mA the LED lighting applications employ the most frequently. LPC-100 operates for the range 90~264VAC so it can perfectly work for most of the countries in the world. The whole series is based on class II (without FG pin) design, housed with a 94V-0 flame retardant plastic case. With the working efficiency up to 90%, LPC-100 can work at the ambient temperature between -25℃~+50℃ under air convection.
Features
- Constant current design
- Universal AC input/full rauge
- Withstand 300VAC surge input for 5 seconds
- High efficiency up to 90%
- Protections: Short circuit / Over voltage
- Cooling by free air convection
- Fully encapsulated with IP67 level (Note.6)
- Fully isolated plastic case
- ClassⅡpower unit, no FG
- 100% full load burn-in test
- Low cost, high reliability
- 2 years warranty (Note.4)
Specifications
OUTPUT
- RATED CURRENT
- 1400mA
- CURRENT ACCURACY
- ±5.0%
- CONSTANT CURRENT REGIONNote.5
- 36 ~ 72V
- RATED POWER
- 100.8W
- RIPPLE CURRENT
- ±5%
- VOLTAGE TOLERANCE
- ±1.5%
- SETUP, RISE TIME
- 1000ms, 80ms / 230VAC 2000ms,80ms/115VAC at full load
- HOLD UP TIME (Typ.)
- 16ms/230VAC 10ms/115vac at full load
INPUT
- VOLTAGE RANGENote.2
- 90 ~ 264VAC 127VDC ~ 370VDC
- FREQUENCY RANGE
- 47 ~ 63Hz
- EFFICIENCY (Typ.)
- 89.5%
- AC CURRENT (Typ.)
- 2.2 A / 115VAC 1.2A / 230VAC
- INRUSH CURRENT (Typ.)
- COLD START 75A(twidth=980μs measured at 50% Ipeak) at 230VAC
- MAX. No. of PSUs on 16A CIRCUIT BREAKER
- 1 units (circuit breaker of type B) / 2 units (circuit breaker of type C) at 230VAC
- LEAKAGE CURRENT
- <0.25mA / 240VAC
PROTECTION
- SHORT CIRCUIT
- Hiccup mode, recovers automatically after fault condition is removed
- OVER VOLTAGE
- 80 ~ 97V Protection type : Shut down and latch off o/p voltage re-power on to recovery
ENVIRONMENT
- WORKING TEMP.
- -25 ~ +50℃ (Refer to "Derating Curve")
- WORKING HUMIDITY
- 10 ~ 95% RH non-condensing
- STORAGE TEMP., HUMIDITY
- -40 ~ +80℃, 10 ~ 95% RH
- TEMP. COEFFICIENT
- ±0.03%/℃ (0 ~ 50℃)
- VIBRATION
- 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC
- SAFETY STANDARDS
- IEC 62368-1;EAC TP TC 004, IP67 , BS EN/EN62368-1 approved
- WITHSTAND VOLTAGE
- I/P-O/P:3KVAC
- ISOLATION RESISTANCE
- I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
- EMC EMISSION
- Compliance to BS EN/EN55032(CISPR32) Class B; BS EN/EN61000-3-2 Class A(≦80% load); BS EN/EN61000-3-3, EAC TP TC 020
- EMC IMMUNITY
- Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55035, light industry level , EAC TP TC 020
OTHERS
- MTBF
- 4121.8K hrs min. Telcordia SR-332 (Bellcore) ; 511.2K hrs min. MIL-HDBK-217F (25℃)
- DIMENSION
- 190*52*37mm (L*W*H)
- PACKING
- 0.61Kg;20pcs/13.2Kg/0.55CUFT
Test conditions and notes9
- 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
- 2. Derating may be needed under low input voltages. Please check the static characteristics for more details.
- 3. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
- 4. Refer to warranty statement.
- 5. Constant current operation region is within 50% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design.
- 6. Suitable for indoor use or outdoor use without direct sunlight exposure, please avoid immerse in the water over 30minutes.
- 7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
- 8. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
- 9. This product is not intended for LED lighting luminaire applications in the EU and China.(In the EU and China the LPF/NPF/XLG/XLC/XLN series are recommended.)
Technical drawings
Typical applications
- Display devices for decorative & advertising accessories (Note.9)
Downloads
FAQ
Can I use the LPC-100-1400 for high-power LED downlights?
Yes, if the downlight requires a constant current driver at 1400mA and the LED load stays within the 36-72V constant current range. This model can deliver up to 100.8W, so it fits higher-power constant current downlight assemblies rather than constant voltage lighting. Note that the datasheet states it is not intended for LED lighting luminaire applications in the EU and China.
Is the LPC-100-1400 suitable for signage modules or backlit channel letters?
It can be suitable for signage modules when the module string is designed for constant current operation at 1400mA and the total forward voltage falls between 36V and 72V. It is not the right choice for constant voltage signage systems that expect a fixed DC output.
Can this driver run a small LED array for architectural or display lighting?
Yes, for a small LED array that is specified for 1400mA constant current and has a combined forward voltage inside the 36-72V range. With 100.8W available, it is aimed at larger constant current LED arrays rather than low-power modules.
How do I know if the LPC-100-1400 is compatible with my LEDs?
The key match points are 1400mA constant current output and a 36-72V CC range. The number of LEDs depends on the forward voltage of each LED, so compatibility is based on the total LED forward voltage, not a fixed LED count.
Can the LPC-100-1400 be used outdoors or in damp locations?
Its IP67 rating makes it appropriate for damp or dusty locations, and the datasheet allows indoor use or outdoor use without direct sunlight exposure; avoid immersion in water over 30 minutes. The operating temperature range is -25°C to +50°C, so the installation environment needs to stay within that range.
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Please log in to write a review.
Write a review
Reviews are checked before publishing. By submitting you confirm this is your genuine experience with this product.
Submitting your review…
It's published and now helps other buyers.
We're checking it and it'll appear shortly.
Please try again.







